“For years now, DJ Vibe has been in partnership with Recess
from www.recess.co.uk to spread the knowledge of how to DJ. In that
time, many DJs have learnt how to mix from this text on this site,
and Recess has expanded on the info and turned it into one of the
well known Dummies series of books – DJing for Dummies.’
To
give you a taster of the info contained in the book and his website,
we happy to host the original text as a testament to how some folks
like to help out others. Take a read through these guides, visit
his website, and buy the book – it’s the first step
to becoming a DJ.”
One
of the first things that most people will tell you when you think
of getting into this game is to try it out on someone else's equipment
before you put your hard earned money into it. FANTASTIC
idea. But what if you don't know anyone who is either willing, or
has the equipment to let you practice on? You could always try to
find somewhere that'll let you rent gear from them (I don't know
of anywhere before you ask!) but not a lot of places do that. So,
I'm afraid you have to think about buying stuff - sorry. Providing
that you're looking to become a Vinyl using Dj, then there are a
few basic thing that you are going to need:
2
x Turntables
2 x SlipMats
2 x Cartridges and Needles for the Turntables (normally included)
1 x Mixer
1 x Pair of Headphones
Something to amplify the signal (Stereo, Amplifier + Speakers
etc.)
So,
apart from some tunes and some really friendly neighbours, thats
should hold you for a while.
The
one thing I'll say though before I go into each of this lot is that
it's a good idea to spend as much as you can on the turntables,
then whatever you have left on the rest of the gear. You can use
a bad mixer with good decks without too much problems, but not even
the best of mixers is going to compensate for bad decks. Plus, it's
a lot cheaper to upgrade a mixer when you get round to that point
than it is to upgrade your turntables.
TURNTABLES
The first
thing you really have to make sure of is that there is a control on
the turntable which allows you to adjust the pitch (the pace at which
the record will be played at) of the record. Just a 33 or 45rpm setting
is not enough. You're looking for something that will allow the pitch
to be adjusted by AT LEAST + or - 8%. The larger the pitch control,
the better. One that runs most of the right hand side of the turntable
is preferred and is the industry standard for pitch control. The length
allows more fine adjustments than just a small control on the front
of the unit (see the Gemini XL-100 as the method you DON'T want
to get.
The
next, and biggest choice you have to make when you are on a shoestring
budget is whether to buy DIRECT DRIVE or BELT DRIVEN decks
(another word for Turntable or CD unit). I'm not going to get
into a hefty description of the differences between the two right
now, but if you're interested before reading on, then click HERE
to go to the section in my Extra Stuff page which goes into a bit
more detail.
Suffice to say, direct drive
decks are by far the preferred means of powering the deck. Simply,
because the Belt Driven decks use a rubber band and an intermediate
to drive the deck, a lot of the power and accuracy is lost through
the transfer of that power. This means that the pitch settings that
you choose might not be held for long enough, meaning the tempo
of the song you are playing will change while in use, causing havoc
when trying to beat match. It also means that the deck does not
have the power (or TORQUE) to withstand the vigours of scratching,
and has a very poor start up time.
The
problem is though, that cheap Direct Drive decks will still have
similar problems, though not to the same extremes that the Belt
driven decks will have. The power to the deck is still somewhat
lacking compared to the better quality (and more expensive) models,
and they can still have a tendency to lose their pitch settings
slightly.
As
I said before, I DO urge you NOT to get belt driven
decks, but as so many people have hardly any money when they start,
combined with a yearning to be a Dj, it might be something you settle
for. Just don't come running to me when they start playing up on
you!!
AND
, I'm going to say this again. It seems to be lost on people,
maybe they aren't reading this far into the site (1 page, lazy buggers!)
but I'm going to re-iterate this now.
Belt
Driven decks suck. This isn't from a "To be a Dj you must have Technics"
point of view. It's the truth. Belt-Driven decks suck. You'll hear
people telling you that they're using Belt-Driven decks, and there's
nothing wrong with them, "Oh yeah, I've had mine for years, can
do anything on them, scratch, mix, cook, play frisbee, solve the
worlds debt and hunger problems...." Fine. If you want to listen
to them rather than me, then I'm not going to get all fussed and
bothered about it, but PLEASE, stop asking me if it's OK to use
Belt-Driven decks, then bugging me about it for two weeks, ignoring
what I say, then sending me a mail two months later saying "Yeah,
you were right, they suck. How can I make them better?" At which
point, I just hit the delete button. It's the only thing I'm a wanker
about. This is something I feel passionate about, that belt-driven
decks are for people who either a) Aren't serious about Dj'ing,
b) are only going to use them for a couple of months as a test to
see if they're going to like Dji'ng, or c) Think with their wallets
instead of thier heads.
So,
there are things like Soundlab's DLP30's (I think), Numark's TT-1700's,
Gemini's XL-400's, Kam's BDX something's which are built to emulate
a Technics deck, but don't quite have the power or pitch accuracy
to be that much use after you've learnt to beat match. If you MUST
go out and spend as little as you can, then look at these decks.
I really would like it if this is the last I have to mention of
not using them, I'm getting ready to punch my computer the next
time I get a mail asking me about them. I was pretty sure that I'd
plastered "Don't use belt decks" enough over my site already!! :-)
BUT,
the thing I will stress, no matter how shoe-string your budget is,
no matter how unserious you are about dj'ing (unserious? Someone
get me a thesaurus) no matter how long you'll be using them before
you know you'll buy better decks, DO NOT, I REPEAT
DO
NOT
Use
the Gemini XL-100 or the Soundlab DLP-1600 decks. These decks are
NOT meant to be used as Dj decks. Yes, people like Sapphires advertise
them as decks you can use, but you'd be better pissing off your
cat so it'd stick out its claw, then making it run round the record,
caterwauling as if to reproduce the tune you're playing. You'll
have better power, pitch control and care for your records with
the cat than you would with the XL-100 or DLP-1600. I can not stress
enough NOT to use these decks. If you're cheap, go for the ones
above, don't be fooled by the "Yeah, these are Dj decks" and the
price tag. You'd be better getting "I'm a cheap twat" tattood on
your head BACKWARDS for the money, rather than buying these.
Anyway,
rant over, on with the site again........
Most
likely, for a small budget, you'll be looking at this lot (no particular
order):-
Belt
Driven Decks
Direct
Drive Decks
Soundlab
DLP1
Soundlab
DLP3R
Gemini
XL-400
Gemini
XL-500/600
Numark
TT1700
Numark
TT1910
Kam
BDX180
Kam
DDX580
sorry,
ran outta decks!
Citronic
PD-1 (best of the lot)
Yes,
I know there's a lot more makes and models out there, American
Dj, Limit, Sherwood, etc etc, but the ones above are the ones
I have had even the slightest of time on, and I'm loath to include
stuff I've never used.
Here's
where I put in a disclaimer though. The decks that I mentioned
above will just about do for normal beat mixing styles (trance,
house etc) but if you're thinking of doing ANY scratching at all,
then you're wasting your time and money considering any of these
decks. For start, belt driven decks are RIGHT out of the
question. The other decks I mention, though direct drive, just
don't have the power to the deck plate to make scratching a viable
option on them, they just aren't made to cope with the vigours
of scratching. I've put a bit about equipment on the Scratching
page on this site. Read that if you're interested in Scratching
gear.
The
purpose of the slip mat is to reduce the friction between the
record and the turntable to the point where you can hold the record
still, and the turntable will still turn underneath it (which
is yet ANOTHER problem with basic, cheap decks, their power is
so weak that this won't happen). The setup should go like this:-
At the very bottom, is the deck plate in all it's shiny glory
(make sure to take off the removable rubber mat that comes with
the deck (NOT the rubber coating, the rubber mat). On top of that
goes the slipmat, and on top of that goes your finest record.
As
mentioned, there can sometimes be problems with the decks that
causes the deck to come to a grinding halt when you are trying
to cue up the record. The way to try to get around this is to
reduce the friction further between the deckplate and the slipmat.
This can be done by either cutting a six inch diameter circle
piece of cardboard out, punching a hole in the middle, then sitting
this between the slipmat and the deck plate or by cutting out
a piece of wax paper (some inlays in record sleeves are wax paper)
to the size of your slipmat, and putting THAT inbetween the plate
and the slipmat. The second option there is by far preferred,
by putting the piece of cardboard between the two, the friction
IS reduced, but so if the stability of the record, so you may
find the needle jumps a lot. Go for the wax paper if you're having
issues.
Try
to steer clear of the mats with lots of printed designs on them
too. They can (sometimes) damage your records, and they are (sometimes)
not as effective as plain felt ones.
I
don't really know the part where it comes to what makes and models
(if there are models) of slip-mats are best, but, the Technics
ones are damn good, a great choice. Just look for generic hip-hop
ones, coz they're designed to be very slippy. The best ones I've
ever used are ones I got from M2 (The people who sponsor my equipment
pages). They're light, thin and minimal printing on them, making
them perfect.
The
purpose of the mixer is to change the sound you can hear from
one turntables output to the other ones, without having a break
in sound. Typically, this means that deck 1 is in Channel 1 and
deck 2 is in Channel 2. To change from one channel to another,
a cross fader is normally included on the mixer, which, as you
move it, moves the sound from one deck to the other.
When
you're starting off, you are going to be fine with a really basic
mixer like Numark's BlueDog. Ok, if you have the money, get something
better, but again, I'm just talking bare minimum equipment right
now. The problems that you'll encounter with a very basic mixer
should only add up to sound quality issues. With no kills or cuts
on the mixer, you'll find that a lot of the times the bass drums
and bass melodies will clash with each other, and with no Gain
controls, or means to measure the strength of the incoming signal,
you'll find that there will be mismatches in the levels (volumes)
of each tune as you go through the mix process.
Just
make sure it's not so basic that it doesn't have a cross fader,
or it doesn't have a headphone cue on it. By headphone cue, I
mean a means that you can listen to (monitor) the turntable that
ISN'T playing out of the speakers. A normal cue will allow
you to listen to the unheard turntable and the live (playing through
the speakers) turntable at the same time and will have a slider
or a rotary knob which lets you adjust the volume at which you
hear either of them. This allows you to be more precise when it
comes to matching the beats.
These
are what transfer the vibrations caused by the grooves in the
record to sound. The needle (Stylus) itself sits inside the groove
of the record, and as the record passes through it, it vibrates.
The cartridge hold the needle, which is then screwed onto the
headshell, which is locked onto the tonearm - all of which translate
the vibrations to an electrical signal which is turned into the
music that you hear.
There
are MANY different kinds of Needle and cartridge (cart for short)
out there, but the chances are the ones that you'll get included
with the decks will be Stanton 500AL's. Check to see whether they
are included with your decks or not, as there's nothing worse
than taking all your stuff home, only to find that you can't use
anything because of missing equipment.
AMPLIFIERS
The
signal that comes out of the mixer is barely strong enough to
power your headphones, so you need something which will increase
(amplify) this signal so that it will drive (make 'em work) a
pair of speakers.
There's
three choices (as far as I see it) to how to do this:-
1)
Buy a separate amplifier and speakers. This can be a bit costly,
but it is a great way of doing it.
2)
Plug the output cable into either the CD or AUX port in the back
of your stereo (if you have one) . This is what I do at home.
I prefer this method because it cuts down on the amount of equipment
you need (and so money you'll have to spend) and it means that
there's already a built in tape recorder, or MiniDisc recorder
etc. to record your mixes. DON'T use the PHONO input though.
The Phono inputs use a completely different means to process the
signal, and are only meant for Turntables. Though you ARE using
turntables, the signal you are using is from the mixer, which
is known as a LINE signal and is far stronger than that
of a turntable, and therefore can't go into the PHONO input.
3)
Using POWERED speakers. A few people that have written to
me over the year or so that I've had this site up have used these.
Really, they are just speakers with a built in amplifier, so you
have to plug them into a power socket, but, provided they are
powerful enough to let you hear the music loud enough, the will
suffice. A few people I know actually use the powered speakers
from their computers. For professional use, the JBL EON PWD 10
is great, I've seen it used a lot for the monitor in the DJ booth.
So
apart from getting records to play, and having some nice understanding
neighbours, that's the basics of what you need. Ok, there's stuff
like something to keep your records in, and something to put your
decks and mixer on, but you can work that one out yourself.
RSS | 
Twitter | 
Facebook | 
Youtube 
One
of the first things that most people will tell you when you think
of getting into this game is to try it out on someone else's equipment
before you put your hard earned money into it. FANTASTIC
idea. But what if you don't know anyone who is either willing, or
has the equipment to let you practice on? You could always try to
find somewhere that'll let you rent gear from them (I don't know
of anywhere before you ask!) but not a lot of places do that. So,
I'm afraid you have to think about buying stuff - sorry. Providing
that you're looking to become a Vinyl using Dj, then there are a
few basic thing that you are going to need:
Suffice to say, direct drive
decks are by far the preferred means of powering the deck. Simply,
because the Belt Driven decks use a rubber band and an intermediate
to drive the deck, a lot of the power and accuracy is lost through
the transfer of that power. This means that the pitch settings that
you choose might not be held for long enough, meaning the tempo
of the song you are playing will change while in use, causing havoc
when trying to beat match. It also means that the deck does not
have the power (or TORQUE) to withstand the vigours of scratching,
and has a very poor start up time. 
